published |
DOI
http://dx.doi.org/10.25098/1.2.2212 |
Issue |
Vol 1- Issue 2
Dec 2017
|
Section |
Engineering |
Sergii O. Kroviakov1
Andrey V. Mishutin2
Odessa State Academy of Civil Engineering and Architecture, Odessa, Ukraine
Received : 6-7-2017 Revised: 15-8-2017
Accepted : 20-8-2017 Published : Dec 2017
Abstract
Because of the maximum uplift water pressure usually became under the gate of the hydraulic structures, so in this research a determination of the uplift pressureunder the gate location was investigated by using a finite element method with the Geo- studio 2016 software together with experimental work by using electrical analogue model to compare the results obtained from the two methods and to show the accuracy of the electrical analogue model to simplify solving the seepage problems under the hydraulic structures.
The experiments were carried out in the electrical laboratory, Kut Technical Institute, for four cases of impervious layer at different depths of (75, 60, 45, 30) cm respectively, and each case consisted of (25) models, the flow net was plotted for each case and the total was (100) cases to determine the uplift pressure beneath the gate location.
The experimental flownets and results were compared with the results of Geo-studio software program, both results shown a good agreement between them approach to (92.561)%.
Keywords: impervious layer, uplift pressure, SEEP/W software, electrical analogue model.
پوخته:
بههۆى بهرزى پهستان لهسهر بنكهى دهرگاى دامهزراوه هایدرۆلیكیهكان، ئهم توێژینهوهیه ههوڵدهدهات برى ئهو پهستانه لهو جێگانهدا دهستنیشان بكات لهرێى میتۆدى رهگهزى بێكۆتاوه (Geo- Studio 2016 SEEP/W) وه هاوتاكردنى دهرئهنجامى دهستكهوتوو به دهرئهنجامهكانى كارى تاقیگهیى كه له رێگهى بهكارهێنانى مۆدێلى ئهنهلۆگى كارهبایى یهوه دهست كهوتوون به مهبهستى ئاسانكارى له چارهسهركردنى لێچوون له دامهزراوه هایدرۆلیكییهكاندا.
تاقیكردنهوهكان له تاقیگه كارهبایى یهكانى بهشى كارهبا له پهیمانگاى تهكنیكى كوت ئهنجامدراوه. كه تیایدا چوار جۆرى جیاواز له چینى نهبر له قوڵى (75,60,45,30)سم تاقیكراوهتهوه. ههر یهكێك لهم حاڵهتانه (25) نموونه له خۆ دهگرێت و بۆ ههریهكهیان تۆرى ئاوهرۆ كێشراوه و بهم شێوهیهش (100) نموونه دهست كهوتووه. له كۆتادا، دهرئهنجامهكان به شێوهیهكى بهرچاو به رێژهى (92.561%) هاوتابوون.
الملخص
بسبب وجود أكبر ضغط اصعاد تحت موقع البوابة في المنشآت الهيدروليكية, فقد كرس هذا البحث لإيجاد ضغط الاصعاد في هذا الموقع باستخدام برنامج يعتمد على طريقة العناصر المحددة (Geo- Studio 2016 SEEP/W), إضافة الى العمل المختبري باستخدام نموذج التماثل الكهربائي, وقد تمت مقارنة النتائج المستحصلة من الطريقتين لإظهار دقة نموذج التماثل الكهربائي وذلك لتبسيط حل مشاكل التسرب تحت المنشآت الهيدروليكية.
أجريت التجارب المختبرية على الموديل الكهربائي في مختبر الدوائر والقياسات- قسم الكهرباء- المعهد التقني في الكوت. لقد تم فحص أربع حالات لأعماق مختلفة من الطبقة العديمة النفاذية وهي على التوالي (75, 60, 45, 30) سم وكل حالة تتضمن (25) نموذج وقد رسمت شبكة الجريان لكل حالة حيث أصبح المجموع الكلي للحالات (100) حالة, وذلك لإيجاد ضغط الاصعاد تحت المنشأ الهيدروليكي في موقع البوابة, ان المقارنة بين نتائج العمل المختبري والبرنامج النظري قد أعطت توافق جيد يصل معدله الى (92.561)%.
.
.